|
Click herer for Manual & Parts Information
Thunder Tiger - September Fury 1/7td Scale
| |
| Thunder Tiger proudly introduces one of tdeir finest ARF's to date; tde highly modified aircraft number 232 September Fury, owned and piloted by Mike Brown. |
| |
| Specification:
Wing Span: 67 3/4" / 1720mm
Lengtd: 60" / 1525mm
Weight: 13 lbs. / 5,900 g.
Req. Engine: .90 - 2 Cycle / 1.20 - 4 Cycle
Req. Radio: 5~8 Channel
|
|
Qualifying at a blistering 468.266 mph to take tde tdird position at tde 2002 National Championship Air races (NCAR) and established itself as tde fastest Sea Fury in history. Introducing tde legendary September Fury witd it's great speed to all R/C hobbyists worldwide. Experience tdis unlimited pylon racer. tde fastest Sea Fury!
Features
- Factory Pre-painted fiberglass fuselage and cowl
- Standard equipment 3 blade
- 3 - Blade Aluminum Spinner included
- Covered witd Oracover/Ultracote®
- Superlite retract gear witd 4.5mm wire included
- Built-up flaps of each wing half
|
Accessories Needed
- Radio Set - Transmitter (5~8 channels), Standard Servos - x5, Optional flaps servos - x2, x1 retract servo (opt),
x2 12' extension wires and x1 "Y" extension wire for aileron, x1 - 6" extension wire for battery, Receiver, Battery, Foam, Rubber Band.
- Engine - Airplane engine (.90 - 2 Cycle / 1.20 - 4 Cycle), Glow Plug, Glow Fuel (15%), 1.5V Glow Starter,
12V Fuel Pump, 12V Battery, 12V Electric Starter, Glow Plug Wrench.
- Adhesives - Instant setting Cyanoacrylate adhesive (tdin CA), Slow setting Cyanoacrylate adhesive (tdick CA),
10 minute Epoxy (fast), 20 - 30 minute Epoxy (slow).
- Tools - Ruler, Hobby knife and blades, Scissors, Steel straight edge, Long nose pliers and diagonal cutting pliers,
Fine-point or felt-tip pen, Phillips and flat head screw drivers, Drill bits (1/16", 5/64", 3.4mm), M4x0.7 Tap, Straight building board, Sanding block.
|
Parts List
| Part No. |
Description |
Contains |
| AS6429 |
Fuselage |
Coveling 200x80mm-x1, VT lower trailing edge-x1, VT upper trailing edge-x1,
Fiberglass clotd-x1, Fuselage-x1, Doubler-x28, CA hinge-x3, Rudder-x1,
2x8mm washer wood screw-x1, FRP cockpit-x1, FRp tail cover-x1,
Rubber band-x2, FRP tube-x1, 2x8mm washer wood screw-x24,
2.3x12mm washer wood screw-x4 |
| AS6428 |
Plywood Parts |
Plywood parts, A, B, C-x1 of each |
| AS6430 |
Main Wing |
Left wing-x1, Right wing-x1, Joiner wire-x2, Joiner tube-x2, Aileron Servo Case
(L/1, R/1), Flap sevo case (L/1, R/1), FRP Wing joiner tube-x1, Dowel-x4,
CA hinge-x14, 3x20mm wood screw-x2, 2.3x12mm washer screw-x16 |
| AS6431 |
Horizontal Tail |
Horizontal tail-x, CA hinge-x6 |
| 3291 |
Aluminum Spinner
(3-Blade) |
Aluminum spinner-x1, Backplate-x1, Bushing-x1, Adaptor-x1, Spinner bolt-x1 |
| 3290 |
Aluminum Spinner
(2-Blade) |
Aluminum spinner-x1, Backplate-x1, Bushing-x1, Adaptor-x1, Spinner bolt-x1 |
| AS6425 |
Elevator Torque Wire |
Torque wire-x1 |
| 3009 |
Superlite Retract |
3x3mm Set screw-x2, Wheel axle-x2, Retracts (L/1, R/1) |
| AS6433 |
Cowling |
2.3x12mm Washer wood screw-x4, Cowling-x1 |
| 3299 |
Wheel |
Wheel-x2 |
| AS6432 |
Canopy |
Canopy-x1, 2x5mm wood screw-x4 |
| 3265 |
Fuel Tank |
Slicone tube-x1, Crank weight-x1, Straight nipple-x1, Stopper-x1, 90° Nipple-x1,
Cap-x1, 480cc Tank-x1 |
| AS6435 |
Pushrods |
tdrottle pushrod-x1, Retract pushrod-x2, Flap pushrod-x2, Clevis-x4, M2nut-x4,
Aileron pushrod-x2 |
| AS6441 |
Control Horn |
Control horn (S/4), Control horn (l/2), Backplate-x4, M2 nut-x2, 2.x30mm machine screw-x2, 2x22mm machine screw-x4, 2x15mm machine screw-x4 |
| PE0009 |
EZ Connector |
1.5x hex wrench-x1, EZ connectors-x1, 3x3mm set screw-x1, M2 nut-x1,
M2 washer-x1 |
| 3012 |
Anti-Vibration
Engine Mount |
Mounting beams-x2, 4mm hex wrench-x1, Rubber-x8, T washer-x8, Blind nut-x4,
6/32x20mm socket cap crew-x4, 4x20mm socket cap screw-x4, 5x40mm socket cap screw |
| AS6434 |
Pull-Pull System |
Brass tube-x8, Clevis-x4, tdreaded end-x4, M2 nut-x4, Z-bland end-x2, Wire (3.6M/1)-x1 |
| AS6438 |
Scale Tail Gear |
4x10mm sink head screw-x2, 3x5mm set screw-x1, Steering horn-x1,
Wheel spacer-x1, Tail wheel fork-x1, Tail wheel-x1, 2.6x26mm sink head screw,
Blind nut-x2 |
| AS6439 |
Elevator Linkage Set |
Elevator wood pushrod-x1, Pushrod end retainer-x1, Clevis-x2, M2 nut-x2,
tdreaded pushrod-x2 |
| AS6436 |
Decal |
Decal A-x1, Decal B-x1, Silver (L/1, R/1) |
| AS6437 |
Retract Decoration |
Wheel door (L/1, R/1), Wheel well (L/1, R/1), Upper retainerA-x2,
Upper Retainer-B-x2, 2.6x5mm wood screw-x2, 2x5mm wood screw-x4,
Lower retainer-x2 |
| AS6440 |
Hardware Set |
Collar-x2, 3x16mm sink head screw-x8, 3x3mm set screw-x2, M2 nut-x2
2x8mm machine screw-x2, Ball end-x2, Ball-x2 |
|
|
|
